Carpet for boat trailer bunks is a covering that is placed on the bunks of a boat trailer in order to protect the boat from scratches and scuffs. The carpet is usually made from a durable, synthetic material that can withstand the elements and wear and tear from the trailer.
20 Best Carpet For Boat Trailer Bunks
1. C.E. Smith Carpet Roll – Blue – 11″W x 12’L
Marine grade carpet; Weather resistant
High quality 100% PET polyester
Durable backing; Minimal water retention
16.1 oz. per square yard weight; Pile height of 5/32″
Replace worn carpet on your boat trailer’s bunks and help protect your boat’s finish with this durable, weather-resistant carpet. Marine-grade polyester won’t trap in moisture. Resists mold and mildew.
If you use this on your 2×6 bunk boards, some of the board will be exposed on the underside. Protect Your Boat’s Hull Over time, the carpeting that covers your bunk boards can wear down or even tear apart.
This can lead to scratches on your boat’s hull. Replacing the carpeting periodically ensures protection for your boat, and it will also prevent your wooden bunk boards from rotting. Replacing Bunk Board Carpeting To get started, remove the old carpet from your bunk boards, doing your best to remove any old staples and bolts from the boards as well.
Cut the carpet to the appropriate length and lay it down so that the backing is facing up, then place your bunk board on top. Make sure that there’s enough extra carpet to wrap around the sides and ends of the board.
Then wrap the carpet around one side and staple it in place. Once you’re done with the first side, tightly pull the carpet around the opposite edge of the board and secure it with staples. Loose carpet can easily snag or tear, leaving the wooden board vulnerable to moisture or damage.
Once both sides are securely attached, tuck any extra carpet at the ends in tightly, like you’re wrapping a package, and secure the ends to the board with staples.
Caliber Marine Trailer Bunk Slides make launching your boat or watercraft easy. The simple-to-install bunk pads reduce loading and unloading effort, so your boat slides effortlessly off the bunks and into the water.
They are unaffected by sun, weather, and seawater. The 10-pad packs come complete with stainless steel attaching hardware. Unique profile provides extra cushioning between boat and trailer bunks. Washout channels allow sand and debris to flush off the slides, away from the hull.
Reduces friction and stress by 400% on the trailer cranking mechanisms, ropes, and bow hooks. Allows you to unload and load your boat in shallower water. Fast and simple installation on both horizontal and vertical bunks.
Made from a low-friction composite which is impervious to sun, weather, and saltwater. Also excellent for use on work stations, lifts, and dollies.
Value Carpets and Flooring Boat Trailer Bunk Padding protects your boat from damage and scratches. Made with the same quality padding as marine carpet. Boat Trailer Bunk Padding is durable and built to last for years.
Glue not included. Made in USA. Protects boat from damage and scratches Same quality as marine-grade carpet Durable enough to last for years.
I bought this because it was the only place that had beige padding, which matches the color of the boat and trailer. Padding seems to be decent quality. As others have said, for a 2×4 bunk, it would be nice to have an extra inch of width.
That being said, 8 inches worked ok for me. Installation is definitely easier if you have somebody to lend a hand. I didn’t use glue, but instead attached with half inch stainless steel staples. The carpet that this replaced was also attached with just staples.
I purchased this product to upgrade the bunks on my trailer which are the standard 2X4 size. The rolls are cut to 8″. A 2X4 measures 3-1/2X1-1/2X1-1/2 which comes to 6. 5 inches. That leaves 3/4″ of material on each side to staple to the 2X4’s.
If you think that’s easy to do buy a roll and try it for yourself. I’ve always been happy with product I have purchased from Bass Pro but this is one product that Bass Pro should demand at least 1″ wider but preferably a 2″ wider product from it’s supplier.
The product is Boat Trailer Bunk Padding Model # 08122 / SKU320702. I would not buy this product again or recommend it to a friend.
I purchased 12 ft x 12 in. wide padding and it was hard to get it wrapped around 2×4 far enough to get staples in it. It should have been 14 in. wide making it a lot easier to install. The biggest problem I have with BP is that I have tried unsuccessfully 3 times since March to get a Master Catalog and I still don’t have one.
I recently installed the four foot long boat bunk boards on a trailer I was modifying for a new Zodiac Aluminum RIB. They were of excellent fit and finish at a fair price. They were part of a larger order and all parts arrived faster than promised.
I was very pleased and I am about to place another order with Wholesale Marine to complete my project.
The carpet itself seems fine, but the eight inch wide version is too narrow, and the twelve inch version is too wide for a 2X4. You want it to wrap under the board, but not overlap. The reason boards fail is water retention.
You want the water to drain, and overlapping the carpet underneath doesn’t allow for that. Poor design.
This polypropylene, weather-resistant carpet is cut to your specifications from a continuous roll. Typically used for 2″ x 4″ bunk boards. Select the required length from the drop-down menu below. If you need longer lengths, just add additional quantities.
Sold by the Foot Cut to the desired length Choose from 3 colors: Black, Dark Charcoal, & Light Gray Completely Covers 2″ X 4″ Boards Replacement trailer bunk board carpet for boat trailer bunks.
This carpet has great texture and does not fray at the edges. It is not thick but thick enough to add good protection for what I needed in replacing the side boards and their carpet on my boat trailer.
I used new Douglas Fir boards (they hold staples well), treated them with boiled linseed oil, (wiped off all residue and sat overnight) and used stainless steel 1/2″ staples. The 11″ wide carpet by the foot was just the right width for the 2×4’s.
I ordered carpet 1′ longer than each board and glad I did; some trimming was necessary due to unsquare cut ends. Carpet stays in place with staples close to edges and folds nicely on board ends. Turned out real nice.
Shipping got mixed up but customer service made quick corrections with priority mail delivery. Very satisfied.
The carpet was plenty wide enough and got a little extra in length. Just put the carpet on yesterday so will give it some time to see how it holds up. The factory carpet from the trailer manufacture held up 6+ years.
Protect your vehicle with Shoreline Marine Trailer Bunk Padding. This durable material functions as insulation between your trailer bunk and whatever you’re hauling. It specifically works to protect the hull of a boat from rough treatment by the sides of the bunk while on the road.
This full pack comes with an 8” x 12” sheet of quality trailer padding. These dimensions let you easily customize the size of the pads. Simply measure your trailer’s dimensions and then cut the sheet down.
The material slices without difficulty to help you make bunk covers that work just right with your equipment. Once installed, the padding uses its strong acrylic backing to give you durability in the roughest conditions.
This carpet stays in one piece during loading and unloading. It stands up to trips down rough roads and keeps your cargo secure. This marine padding’s durable construction also holds up under tough weather.
Product came in quickly and in good shape. Easy to work with and made a huge difference when putting the boat on the trailer. The boat seemed to glide on the bunks much smoother than the previous carpet.
Although the material seemed a bit thin it appears to be durable. The only negative is that the invoice that was shipped with the product showed that I paid $4 more per role. After checking my credit card account I verified that the invoice price was not correct and that I actually paid what was on the Walmart website.
The service was slow (I appreciate the $5 gift card for the late delivery) and the material is of a much lighter weight than I expected. It works fine but for my Kayak but suspect for a heavier boat it would not hold up long.
Boat Trailer Bunk Slick Kit, 10 pieceFeatures Bolts directly onto carpeted bunk boards Fits 2×6 standard bunk boards Slide on or off with less effort Easy to install 10 Pieces 3″ X 16″Bunk Slicks Installation Instructions for #86170 & #86164 With the boat on the trailer, determine the forward most point where the boat makes contact with the bunks.
Unload boat from the trailer. Place Bunk Slick centered on the rear end of bunk so that the bunk slick is even with the end of the carpeted bunk. Space Bunk Slicks on carpeted bunk and space evenly with no more than 4 inches between each Bunk Slick.
Area to be “covered” is from the rear end of the carpeted bunk to 5 inches past the most forward point where the boat hull comes in contact with the carpeted bunk (below). Using the screws provided, attached the Bunk Slicks to the carpeted bunks.
I read a review that said the screws needed to be replaced but I can’t see an indication for that. The screws do not fit neatly between the track but bottom line it works fine. I found this product to be a more cost effective solution to the drag of the carpet than replacing the whole bunks.
I think the price is reasonable but the seller really impressed me with their very fast and free shipping. I’ll be shopping with them again.
Very easy to install. I have always had problems getting my 26 foot pontoon to loading in line with the bunks. Often off by 2 or 3 inches at the rear, but nearly impossible to adjust out of the water.
This year, as the boat was coming out of the water, I noticed the rear was not centered on the bunks again. When the boat was completely out of the water, it slipped over and seated squarely on the bunks.
These bunk slides are heavy-duty and make it much easier to load my boat. Used to have to have just the right amount of bunk showing for the boat to load evenly. Now I can submerge my trailer less in the water showing 2-3′ of bunk and easily drive my 18′ jet boat on while the bunks are still angled which is a really big deal.
Boat self centers now and doesn’t slide to one side or the other. The only negative with these slides is the screws they provide are far too short. I purchased 1-5/8″ stainless steel deck screws with flat tops that look and work great.
These are what they should provide and actually cost less.
Polyester Trailer Bunk Padding Our Happy Customer Reviews 🙂 P P P P PPut together well. Not flimsy and like it’s gonna break. It holds my hair and looks pretty without feeling like it’s gonna fall off.
Buyer Debbie – D638 (3)Vintage Chic Metal Alloy Rhinestone Large Size Fancy Hair Claw Jaw Clips Pins -08/20/19 P P P P PThis seller was a pleasure to work with and I would gladly order from them again.
– Buyer stevet812 (1)Zenteeko Roll-Up Abstract Strategy Board Game for 2 or More Players08/18/19 P P P P PThis transaction went smoothly and I was satisfied with my experience. – Buyer Barbara – B1409 (1)Nature’s Way Alive! Garden Goodness Women’s Multivitamin, Veggie & Fruit Blend08/18/19 P P P P PWorking with this seller was great! I would recommend buying from them.
– Buyer Ute Thanks ! Buyer FJM2 (1)ABCO BH-11-9 Fine Sweep Push Broom – 36″, 3″ Bristles, 4″ Height, 2. 5″ Width, Gr08/05/19 P P P P PWorking with this seller was great! I would recommend buying from them.
– Buyer Claudiac714 (1)NUTRILITE? Complex for Hair, Skin & Nails 60 Tablets08/04/19 P P P P PThis seller was a pleasure to work with and I would gladly order from them again. – Buyer Maurice_George – M (1)Luster Leaf 1818 Rapitest 4-in1 Soil p – H/Moisture/Fertility/Light Tester, Fertili08/03/19 P P P P PI am pleased with the experience I had with this seller.
Two thumbs up. – Buyer Roger – Buyer James – O629 (2)Natural – Care Prosta-Health For Men, 60 Capsules07/29/19 P P P P PThis seller was a pleasure to work with and I would gladly order from them again.
– Buyer Maribel – J5 (2)Vita Value Relax Extra Strength Formula, 30 Tablets07/25/19 P P P P PWorking with this seller was great! I would recommend buying from them. – Buyer Felipe_Farinez I would recommend buying from them.
– Buyer ritah310 (1)Diathrive Diabetes Blood Sugar Kit Diathrive Blood Glucose Meter, 100 Blood Te07/21/19Sgggg BOXES – PLEASE PROVIDE A PHYSICAL ADDRESS Return – Return Return Payment Pay **If you do not have a Pay Select Pay – Pal as the payment method you then will be given the chance to enter your card details in to Pay – Pal account to make paying for your items in the future very easy.
– Feedback Feedback – If you have any queries or BIG ORDER requests, please.
Lancer Marine Carpet 6 X 20 20oz Carpet – Assorted ColorsLancer offers a selection of 11 colors in a pre-cut size for an easy to use Marine Replacement Carpet. The rubber back is flexible and strong, cuts easily to fit any contour and cleans with a broom or water hose.
Nothing updates an older model boat than installing new carpeting, and Lancer’s Replacement Carpeting is the same high quality used by many OEM marine builders. Tough, Long-Wearing Cut pile UV stabilized Olefin pile is naturally stain resistant.
The added UV stability of the colors assure you a long-lasting colorful mat for years of use. Cleaning is easy – with broom, vacuum, or water hose. Easy to Install. Just make a pattern of newsprint taped together and fitted, transfer to carpeting and cut with utility knife or shears.
Glue into place with Lancer’s Marine Carpet Adhesive or other outdoor quality adhesive.
The carpet is much thinner and light weigh than I though it would be. The rubber back is basically a light coating of rubber to hold the yarn. The edges fray very easily and if wrapping it around something the backing shows through on the corners.
I am using it for bunks on a trailer and there is not as much padding as I would like. Glue hopefully will make up for that. I would not use it as a boat carpet that has to be removed. Perhaps if it’s glued down as recommended.
My boat has removable carpet and would never glue down to deck.
The roll of carpet had a manufacturing defect in one section (a large stringer had pulled out and was embedded in the backing). As the roll is quite large I was able to work around it for my boat trailer bunk & fender well project.
Carpet color was spot on and the carpet appears to be of good quality. Make sure to use a sharp knife or scissors when cutting to reduce fraying.
I got this to replace the long worn out carpet in my 29 year old Lund. I was a little disappointed in the color choices, nothing available was as bright a red as the OEM carpet but the ‘Wine’ that I ordered does seem to match pretty well with those portions of the old carpet which has not yet been replaced.
The carpet cuts nicely with a hot knife and installation seems to have gone well (I have been doing more of the watching than the doing).
Makes launching your boat or watercraft easy, slides effortlessly off bunks and into the water. The new unique profile provides extra cushioning between the boat and trailer bunks. Washout channels flush sand and debris off of the slides and away from the hull.
Safer unloading and loading because of reduced friction and stress by 400% on the trailer cranking mechanisms, ropes and hull bow hooks. Allows you to unload and load your boat or watercraft in shallower water.
Fast and simple installation for both horizontal and verticle bunks. Made from a low-friction composite which is impervious to sun, weather and salt water. Excellent for use on work stations, lifts, boat and watercraft dollies.
These things work like a champ! I had traditional carpet wrapped bunks and they made loading and unloading my boat a pain. Since I planned to replace my boards anyways, I decided to skip the carpet and install only the slides on a bare treated board.
Carpet holds moisture, dirt, and debris. moisture rots the boards, and the dirt and debris can damage your hull. These slides have “washout channels” that rinse easily even underneath too keeping the boards high and dry.
if you have an aluminum hull boat (like I do) you WANT these things. not only does the boat slide on and off the trailer easier and in more shallow water, they are safer for your boat too! See, you cannot put an aluminum hull boat on pressure treated wood wrapped in carpet because the chemicals used to treat the wood will leach into the carpet and corrode your aluminum hull! I can now drive my boat almost all the way up the trailer with little throttle and easily winch it up the rest of the way with ONE HAND! Make sure to follow all safety precautions because these things are really slick! Especially when wet.
Used on my pontoon boat trailer instead of recarpeting the bunks. I replaced the old 2×6 treated boards with new 2×6’s and centered these where the pontoons normally sit so the 4inch width of these worked ok as only a small part of the pontoon diameter would touch these.
I painted the new wood blackalso before installing these slides and took the trailer to the lake where the pontoon boat loaded back on the trailer efortlessly. I also used two leftover foot long pieces on the two stops in the front of the trailer that stop the pontoon boat when it gets properly loaded- instead of recarpeting those also.
I wanted to give these a try because a buddy of mine just put some on his and is raving about them. First, they are very easy to install, no tricks just screw them in and they provide stainless screws.
If your wood under the carpet is getting bad, then you will want longer screws. It makes loading take at least less than half the power to get the boat on and saves you carpet from wear. Unloading is also easier but not to worry about it falling off as you are backing up! When it is dry there is enough stick to it that I unhook the front strap.
Don’t know how long these will last but see no reason I should not get years and years of use. When they do wear out, I will just replace them new ones. Love them that much!!! I fish all year and on a regular basis for I am now retired and spend as much time on the lake as I can.
Use the Ozark Trial Marine Trailer Bunk Carpet Replacement Padding to protect your boats hull and make loading and launching much easier. This padding is 11 inches wide and comes in a 12-foot-long roll to fit most bunk and rail sizes.
Easy to install, simply roll out the carpet to the size you need, stretch, and staple on to your bunk. The construction is weather-resistant and durable, and the color is a neutral black. If your bunk carpet is looking old and tired, replace it easily with the Ozark Trail Bunk Carpet Replacement Padding.
Carpeted bunk boards provide proper center loading even in wind or side current conditions. Adjustable boat guides can be fine-tuned to work with your boat and your trailer. The pre-galvanized steel support posts mount horizontally on top of or below your trailer’s frame rail.
Just slide the posts into the boat guide supports and secure the posts so that the distance between the bunks correctly matches the width of your boat. The bunk boards then tilt to conform to the boat’s hull.
Guides will help to center your boat during loading and to hold the boat during transport. Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized. The edges of the pre-galvanized parts often lose their zinc coating during the stamping process.
Because of the thinness of the coating less than 1 mil and the fact that the edges remain exposed, pre-galvanized parts can begin to oxidize and rust quickly, so its recommended that they be primed and painted.
Purchased this for my Fishing boat trailer (16 ft Lowe Boat on Karavan Trailer) The trailer had a low profile roller on the back but was not quite enough to securely mount the boat on the trailer as easily as my larger boat/trailer (24′ Sea Ray) installation was pretty straight forward, but getting it to the exact distance I wanted was a tad bit of a challenge as it moves quite a bit as you tighten the bolt.
I ended up mounting it upside down (tube on the bottom, not on the top of the frame) because of the clearance I wanted to the bottom of the boat, and worked without any issues. I think having an extra hand makes it a lot easier to mount these properly to the frame.
The quality of the product is perfectly fine, and the hardware works well. I wish the metal hardware came in a black color to match the rest of the boat, but that is easily painted. With that said, I am very happy with the product and would buy it again if i needed a guide-on for another trailer.
As for the order with Wholesale Marine, I am very happy with the product, price and also customer service. When I called to get the tracking number (shipped the next day) the rep was super friendly.
These bunks are a real headache saver. I needed something to assist with loading and unloading when fishing solo. It was a toss up between the Guide post or these bunks. Man, I am glad I went with these bunks! It’s like loading by boat into a chute.
I really have to make the boat get out of alignment to have a bad experience. Just aim between the bunks and the boat will line right up. Another reason I went with the bunks was because they can handle more weight while loading.
Installing was a bit more hands on than the packaging insinuated. However, with a drill, some bits, etc and a little know how. I installed them in about 2 hours in the dark with a flood light. Not hard at all.
These went on very easily. Needed to cut some unneeded length for best fit, not an issue. First time loading the boat, in wind, the boat got hung up on one side. The boat has a splash rim about midway down and that is what got hung up.
Relaunch and reloaded with a paddle stuck between boat and the guide. That worked for that time. Got home and did a bit of a modification. Now, instead of the guides being parallel to the boat, I have them vertical.
Brilliant, I know. Well, we will see, I haven’t tested the design yet. Waiting for a windy day.
Get your boat into the water without worrying about harmful friction again! Launch & load your boat with the greatest of ease by installing some TACO Marine Trailer Glyde Sliks on your trailer. Glyde Sliks mount right on your carpeted bunk boards.
All kits include stainless steel screws and instructions. They are economical, injection molded with special anti-friction and UV inhibiting additives, and they have a 3-year replacement guarantee against breakage.
Dimensions: 1. 5″ W x 24″ L. Launch and load with ease Reduces friction Mount on carpeted bunk boards Includes stainless steel screws and instructions Not recommended for aluminum boats with riveted hulls.
Note: If boat is over 2000 lbs. , order 2 sets to install side by side (6 pieces on each side).
Product appears to be exactly what is described. However, like another reviewer they appear to be for lighter boats (under 2000 lbs). I do not see anywhere in the description a warning to limit by weight only length.
I have doubled the glideons on the two 3×8 bunks with two rows and hope when I pull the boat out (Boston Whaler 3000 lbs) they do not crack. Need much better description under specs.
After easy installation of the Slicks, it was time to put the boat back on the trailer. The boat (16′) took very little effort to drive up on. The Slicks were so slick that I had to keep the motor running in forward to attach the winch hook due to the boat sliding back into the water.
Not a very safe thing to do. Warning: If boat is not secured with at least the winch hook in place, there is a good possibility the boat will slide off the trailer while backing down the ramp. Advice: Count the hardware screws that comes with the Slicks.
You should have a screw for every drilled hole in the Slicks. I use a hacksaw to cut the excess length off. It did a good job.
Product was advertised by boat length so I dutifully bought the 16′ set. Only when I received the product and read the instructions did I discover that, if your boat weighs more than 600 pounds, you need TWO sets.
That effectively doubles the price and the installation time. It looks like it might work, but I won’t know until I take my boat out at the end of the summer. In the meantime, BUY BY WEIGHT!.
High quality replacement bunk boards with black marine grade weather-resistant carpet from Shaw protects your boat”s hull from scratches, exhibits very little water absorption, and resists attack from mold or mildew.
Boards are untreated 2″x 4″Southern yellow pine. Additional InformationLength: 5″Pack: 1 pr.
I bought these to replace the guides on the side of my trailer. Fit well, came as advertised and looked good. I used the trailer twice and the carpet has already ripped. These have not been touched since installation.
have not been stepped, no weight bearing, rubbing, etc. Edge of 2×4 was sharp which may have cut the carpet? Also at a glance, 2×4’s are not PT.
All carpet edges were tucked under before stappling. No rough edges to get caught when boat is loaded or unloaded. Would have been nice to know if the wood was treated or untreated to avoid rot!!!! At this price, just trow them away and buy new ones when they are worn out instead of recovering.
Easy to install. Boat holds to the pads when dry. Even on 20 degree boat ramp. Always worry about boat sliding off trailer while backing down ramp. Boat floats right off. Boat slides across pads very easily when wet.
Looks great. Hardware seems good. I added additional screw to help it attach. Took about 1 hour to install on Two bunks. Material is thick but easy to work with.
bought 2 of these to install on my seadoos trailer. did this by myself in a weekend. the 2 Velcro wraps are a big help. suggest you have a very sharp utility knife or a good pear of shears. this is a hard plastic material and hard to hold and wrap around 2×4 like it shows in the store pic.
because it comes rolled up it tends to try and roll it self back up, but using the straps provided I was able to cut to length then screw into place. turned out pretty good for diy project.
This is an excellent carpet for both indoor & outdoor use. This rug is made of polyester fibers and waterproof backing. It is anti-slide, fashionable, and can protect the floor. Easy to clean and maintain, quite suitable for both home and commercial occasions!!! FEATURES: Premium Rug Runner: This large outdoor rug is made of polyester fiber, and it can resist stains, mold, and mildew.
Besides, it is UV-protection and wear-proof for durability. The deep blue color makes it quite modern. Anti-Slide Walking: Ribbed textured on the surface will add traction, and with a 4. 5 mm low pile height, this entryway rug prevents sliding and add no bulk to your feet.
Keep the safety on walking. Water-Proof & Details: The backing layer is made of water-proof TPR and can prevent water penetration. Thus, it can help to protect the floor. This product can be cut with scissors or a utility knife and leaves no fuzz.
Effortless Cleaning: This outdoor area rug is easy to clean with a vacuum machine. Also, easy to sweep or blow debris off. For stubborn stains, you can clean them with a rag and carpet cleaner. Indoor & Outdoor Use: It is perfect for indoor kitchen, bathroom, living room, and outdoor occasions like the patio, porch, deck, boat, sunroom, basement, garage, etc.
Quite practical & convenient. Roll out to use, and roll up for storage. Polyester Fiber Material: This outdoor runner rug is made of superfine polyester fiber, which is UV-resistant and has no mildew for a longer service time.
PRODUCT SPECIFICATIONS: Brand: Vevor Size: 6′ x 13. 1′ Shape: Runner Carpet Thickness: 0. 18″/4. 6 mm Pile Height: 0. 17″/4. 5 mm Weight: 6. 32 lbs Color: Deep Blue Material: Polyester, Fiber, Thermoplastic Rubber.
I bought this for the front area of my garage where the rain comes in and the dog lays around, and maybe an afternoon beer gets spilled from time to time. It is perfect. Water resistant, can be hosed off and the backing doesn’t let it slip around when you walk across it.
It is a fair value if you need to replace it every few summers. I suppose you could use it on a boat or dock too.
Excellent carpet for our screened in porch. Only problem we had was not any fault of the carpet it was more shipping related. The one edge for a little messed up from someone standing it on end. Not a big deal but didn’t realize it until I had it installed.
We are planning to put a rug over those edges that got frayed up a bit.
I am redoing my star craft boat and purchased this carpet. One of the better buys I have bought. The carpet work’s great. It makes the boat look 10 years newer. The one down fall is that the carpet sheds a lot at first.
I recommend this product and would purchase again if needed.
The Amazing Quality ” 11″” Wide x 12′ Long Blue Carpet Roll 11″” wide covers a 2×4 or a 2×6 board Marine grade carpet Weather resistant 100% PET polyester High quality Durable backing Minimal water retention 16.
NOTE: Sold by linear foot. Enter the length (number) of feet as the order quantity. Minimum order of 5′ cut. Our Bass Pro Shops Standard Marine Carpet is backed with marine rubber that can withstand damaging gasoline spills.
Contiguous 48 states orders only. Carpet Glue is needed (not included). Made in USA.
I just finished recarpeting my boat with this. I’m not sure how much longer I’ll keep the boat before I sell it so I used the least expensive carpet. I was pleasantly surprised at the quality of the color.
My best advice to anyone: Using heavy duty scissors will save you a LOT of time cutting. This carpet doesn’t cut well with a carpet knife, regardless of how sharp the blade is. It frays pretty easily on the ends.
I could have saved 5-6 hours if I’d used scissors the whole way. Another tip: use spray adhesive for the edges and corners. Much easier (and less messy) to work with. I used the bass pro shops carpet glue for the flat parts.
Bought a roll kit first, but needed a bit more by the foot. Called the manufacturer direct to make sure I had the right carpet. They were so helpful and told me exactly what to get online from Bass Pro.
This was a great buy! Only took a week for me to get the 16 ft. that I ordered. Great color, it looks amazing. Cuts very easily with a simple pair of scissors. This stuff is extremely easy to work with, I carpeted my entire boat in about 4 hours! I definitely recommend this product.
NOTE: Sold by linear foot. Enter the length (number) of feet as the order quantity. Minimum order of 5′ cut. Our Bass Pro Shops Standard Marine Carpet is backed with marine rubber that can withstand damaging gasoline spills.
Contiguous 48 states orders only. Carpet Glue is needed (not included). Made in USA.
We used this carpet to do the entire bassboat. It has been almost a year since then and I could not be more staisfied with the carpet. It is very easy to work with, to clean, and you can put lures on it without having to worry about having them stuck onto carpet.
I found that using the industrial grade rubber cement applied with a brush is the easiest way to install the carpet.
Body wash for chest acne is a cleansing product that is used to cleanse the chest area. This type of product is typically used to treat mild to moderate acne and can be used on both the body and the face. Chest acne is a common problem that can be caused by a number of…
A gimbal is a device that allows for smooth, stable video footage by compensating for the movement of the camera. It does this by using a motor to keep the camera level, no matter what the orientation of the gimbal itself is. This is especially useful for action cameras like the GoPro Hero 9, which…
Cement board is a type of tile backer board, made of Portland cement, water, and silica, that is used as a base for ceramic or porcelain tile. It is available in 3-foot by 5-foot sheets and in 1/2-inch and 1/4-inch thicknesses. The 1/2-inch thickness is generally used for floors, while the 1/4-inch thickness is used…
The Dutch Bros Secret Menu Frappuccino is a thing to order at Dutch Bros. It’s a blended coffee drink made with chocolate, caramel, and vanilla syrups, whole milk, and ice. 10 Best Thing To Order At Dutch Bros 1. JavaSok – The Original Iced Coffee Sleeve Diamond Back / Medium 22-28oz Product Details Specifications Reviews…
A bench vise, also known as a workbench vise, is a type of vise that is mounted to a workbench. Bench vises are typically used to hold workpieces in place while they are being worked on, such as when sawing, filing, or drilling. Some bench vises also have built-in features that allow them to be…
A mid handicapper is someone with a handicap between 11 and 18, and 5 wood is a golf club with a loft of 18-21 degrees. It’s used for shots that are too long for a 9-iron but too short for a 3-wood, and it’s also useful for tee shots on par-3 holes. 20 Best 5…